Basic Info.
Model NO.
GFC-OLSQxx4XL-CD10
Certification
CE, ISO, RoHS
Transport Package
Antistatic Bag
Product Description
Product Features
- Supports 41.2Gb/s bit rates
- Duplex LC receptacles
- Hot pluggable QSFP+ form factor
- Uncooled 4x10Gb/s CWDM transmitter
- Applicable for10Km on Single Mode Fiber(SMF).
- Built-in digital diagnostic functions
- Low power consumption, < 3.5W
- Unretimed XLPPI electrical interface
- Operating case temperature: 0°C to 70 °C
Applications- 40GBASE-LR4 40G Ethernet
- Infiniband QDR and DDR interconnects
- Client-side 40G Telecom connections
- Other optical links
Product DescriptionsGFC-OLSQxx4XL-CD10 QSFP+ transceiver modules are designed for use in 40 Gigabit Ethernet links over single mode fiber. They are compliant with the QSFP+ MSA, and IEEE 802.3ba 40GBASE- LR4. Digital diagnostics functions are available via an I2C interface, as specified by the QSFP+ MSA.Absolute Maximum Ratings Parameter | Symbol | Min. | Max. | Unit | Note |
Supply Voltage | Vcc | -0.5 | 3.6 | V | |
Storage Temperature | TS | -20 | 85 | °C | |
Relative Humidity | RH | 0 | 85 | % | |
Damage Threshold, per Lane | DT | 3.4 | | dBm | |
Parameter | Value | Unit | Note |
Module Form Factor | QSFP+ | | |
Number of Lanes | 4 Tx and 4 Rx | | |
Maximum Aggregate Data Rate | 41.2 | Gb/s | |
Maximum Data Rate per Lane | 10.3 | Gb/s | |
Protocols Supported | Typical applications include 40G Ethernet, Infiniband, Fibre Channel, SATA/SAS3 | | |
Electrical Interface and Pin-out | 38-pin edge connector ,Pin-out as defined by the QSFP+ MSA | | |
Management Interface | Serial, I2C-based, 400 kHz maximum frequency | | |
Parameter | Symbol | Min | Typ | Max | Units | Note |
Bit Rate per Lane | BR | | | 10.313 | Gb/s | 1 |
Bit Error Ratio | BER | | | 10-12 | | 2 |
Distance on SMF | D1 | | | 10 | Km | 3 |
Notes:- Compliant with 40G Ethernet. Compatible with 1/10 Gigabit Ethernet and 1/2/4/8/10G Fibre Channel.
- Tested with a PRBS 231-1 test pattern.
- Per 40GBASE-LR4, IEEE 802.3ba.
Optical Characteristics (TOP(C) = 0 to 70 ºC, TOP(I) =-40 to 80 ºC,VCC = 3.13 to 3.47 V) Parameter | Symbol | Min. | Typ | Max. | Unit | Note |
Transmitter |
Operating Wavelength | λc | | 1270 | | nm | |
| 1290 | |
| 1310 | |
| 1330 | |
Ave. output power | PAVE | -7 | | +2.3 | dBm | |
Difference in launch power between any two lanes (OMA) | DL | | | 4 | dB | |
Extinction Ratio | ER | 3.5 | | | dB | |
Peak power, each lane | PP | | | 4 | dBm | |
Dispersion penalty, each lane | TDP | | | 3.5 | dB | |
Average launch power of OFF transmitter, each lane | POFF | | | -30 | dB | |
Eye Mask coordinates: X1, X2, X3, Y1, Y2, Y3 | SPECIFICATION VALUES 0.23, 0.34, 0.43, 0.27, 0.35, 0.4 | Hit Ratio = 5x10-5 |
Receiver |
Operating Wavelength | λc | 1264.5 | | 1277.5 | nm | |
1284.5 | | 1297.5 |
1304.5 | | 1317.5 |
1324.5 | | 1337.5 |
Stressed receiver sensitivity in OMA(OLSQ854XM-CDS1) | PSEN1 | | | -11.5 | dBm | 3 |
Average Receive Power,each lane | PAVE | -11 | | +2.4 | dBm | |
Receiver Reflectance | Rrx | | | -12 | dB | |
| | | | | | |
LOS Assert | Pa | -30 | | | dBm | |
LOS De-assert | Pd | | | -12 | dBm | |
LOS Hysteresis | Pd-Pa | 0.5 | | | dB | |
Pin | Symbol | Name/Description | Notes |
1 | GND | Ground | 1 |
2 | Tx2n | Transmitter Inverted Data Input | |
3 | Tx2p | Transmitter Non-Inverted Data Input | |
4 | GND | Ground | 1 |
5 | Tx4n | Transmitter Inverted Data Input | |
6 | Tx4p | Transmitter Non-Inverted Data Input | |
7 | GND | Ground | 1 |
8 | ModSelL | Module Select | 1 |
9 | ResetL | Module Reset | |
10 | Vcc Rx | +3.3 V Power supply receiver | |
11 | SCL | 2-wire serial interface clock | |
12 | SDA | 2-wire serial interface data | |
13 | GND | Ground | 1 |
14 | Rx3p | Receiver Non-Inverted Data Output | |
15 | Rx3n | Receiver Inverted Data Output | |
16 | GND | Ground | 1 |
17 | Rx1p | Receiver Non-Inverted Data Output | |
18 | Rx1n | Receiver Inverted Data Output | |
19 | GND | Ground | 1 |
20 | GND | Ground | 1 |
21 | Rx2n | Receiver Inverted Data Output | |
22 | Rx2p | Receiver | Non-Inverted |
22 | Rx2p | Receiver Non-Inverted Data Output | |
23 | GND | Ground | 1 |
24 | Rx4n | Receiver Inverted Data Output | |
25 | Rx4p | Receiver Non-Inverted Data Output | |
26 | GND | Ground | 1 |
27 | ModPrsL | Module Present | |
28 | IntL | Interrupt | |
29 | Vcc Tx | +3.3 V Power supply transmitter | |
30 | Vcc1 | +3.3 V Power Supply | |
31 | LPMode | Low Power Mode | |
32 | GND | Ground | 1 |
33 | Tx3p | Transmitter Non-Inverted Data Input | |
34 | Tx3n | Transmitter Inverted Data Input | |
35 | GND | Ground | 1 |
36 | Tx1p | Transmitter Non-Inverted Data Input | |
37 | Tx1n | Transmitter Inverted Data Input | |
38 | GND | Ground | 1 |
Notes:1. Circuit ground is internally isolated from chassis ground.Other Pin Descriptions:
ModSelL PinThe ModSelL is an input pin. When held low by the host, the module responds to 2-wire serial communication commands. The ModSelL allows the use of multiple QSFP modules on a single 2-wire interface bus. When the ModSelL is "High", the module will not respond to any 2-wire interface communication from the host. ModSelL has an internal pull-up in the module.ResetL Pin
Reset. LPMode_Reset has an internal pull-up in the module. A low level on the ResetL pin for longer than the minimum pulse length (t_Reset_init) initiates a complete module reset, returning all user module settings to their default state. Module Reset Assert Time (t_init) starts on the risingedge after the low level on the ResetL pin is released. During the execution of a reset (t_init) the host shall disregard all status bits until the module indicates a completion of the reset interrupt. The module indicates this by posting an IntL signal with the Data_Not_Ready bit negated. Note that on power up (including hot insertion) the module will post this completion of reset interrupt without requiring a reset.LPMode Pin
Rayoptek PSM IR4operate in the low power mode (less than 1.5 W power consumption) This pin active high will decrease power consumption to less than 1W.ModPrsL Pin
ModPrsL is pulled up to Vcc on the host board and grounded in the module. The ModPrsL is asserted "Low" when the module is inserted and deasserted "High" when the module is physically absent from the host connector.IntL Pin
IntL is an output pin. When "Low", it indicates a possible module operational fault or a status critical to the host system. The host identifies the source of the interrupt by using the 2-wire serial interface. The IntL pin is an open collector output and must be pulled up to Vcc on the host board.
Address:
3rd Floor, Building 69, Headquarters Business Garden, Nanhu District, Jiaxing, Zhejiang, China
Business Type:
Manufacturer/Factory, Group Corporation
Business Range:
Electrical & Electronics, Manufacturing & Processing Machinery, Service, Textile
Management System Certification:
ISO 9001, ISO 14001
Company Introduction:
As the fixed supplier of the three China National Telecommunications Services Providers (China Mobile, China Unicom and China Telecom). Zhejiang GuangFan Communications Technology Co., Ltd. (member of G. F. Group) has been specializing in communication industry since 2011.
Our trading company and manufacture plant both locate in Jiaxing City, which is in the east of China, with a distance of about 1.5hours by car from Shanghai City. Based on the best geographical position, we can send the products to the customers all over the world economically and efficiently. With own standardize factory and professional team, we promise to provide you high-quality products, professional service and competitive price.
Our aim is to be one of the most professional products, system and service provider in the communication industry. Expecting to become your long-term partner in China.